Allen-Bradley, Rockwell Automation, and PowerFlex are registered trademarks of PowerFlex 4M Adjustable Frequency Drive FRN – User Manual. I/O Wiring. PowerFlex 4M Quick Start Guide. Display. Parameter Group. First Shown when drive powered up. Display Group. (View Only). Basic Program Group. View and Download ALLEN BRADLEY PowerFlex 4M user manual online. FRN 1 Series, FRN 2 Series, Adjustable Frequency AC Drive. PowerFlex 4M.
Author: | Najind Shaktigal |
Country: | Mongolia |
Language: | English (Spanish) |
Genre: | Photos |
Published (Last): | 22 November 2018 |
Pages: | 433 |
PDF File Size: | 15.71 Mb |
ePub File Size: | 1.29 Mb |
ISBN: | 606-4-99646-338-6 |
Downloads: | 76235 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Kagale |
Page 61 Sets the frequency at which the drive will not operate. Page 16 Some local codes may require redundant ground connections. Page 65 [Maximum Freq].
Our Integrated Architecture Solutions provide the foundation to drive plantwide optimization efficiently and effectively, enabling you to respond competitively to the economy and changes in consumer demand.
Page 3 Description for bits 6, 7, and 15 of register address updated.
In this manual we refer to the Po werFlex 4 Adjustable Frequency AC Drive as: drive, PowerFlex 4 or PowerFlex 4 Drive. Parameter numbers and names are shown in this format: The following words are used throughout the manual to describe an action: Similar PowerFlex 4. Smallest and most cost-effective members of the PowerFlex family of drives. The PowerFlex 4-Class of drives consists of two products, the PowerFlex 4 and PowerFlex 40. Available in power ratings from 0.2 to 7.5 kW (0.25 to 10 HP) and in voltage classes of 120, 240 and 480 volts, PowerFlex 4 and 40. PowerFlex 753 AC Drive 86 Rockwell Automation Publication PFLEX-SG002H-EN-P - February 2014 IP00/IP20, NEMA/UL Type Open (continued) Frames 3, 4 and 5 are 600V only drives. Frames 6 and 7 are dual voltage drives and can be operated at 600V or 690V AC.
User Manuals Wiring Diagrams. Basic Program Group A Stop drive before changing this parameter. Based on Drive Rating Display: To find additional product information CAD drawing files, 3D models, etc.
Powerflex 4m Programming
Needed to install, start-up and troubleshoot the PowerFlex 4M Adjustable Frequency AC Drive. This manual is intended for qualified personnel. You must be able to program and operate Adjustable Frequency AC Drive devices. In addition, you must have an understanding of the parameter settings and functions.
ALLEN BRADLEY PowerFlex 4M User Manual
Do not use THHN or allrn coated wire in wet areas. Page 96 Catalog Numbers: Page of Go. Page 78 [Digital Inx Select]. Press and hold in the tabs on each side of the cover. A setting of 0 disables this parameter. Page 26 Each digital input draws 6 mA. Caution should be used when enabling this feature, since the drive will attempt to issue its own start command based on user selected programming. View the content here: Additional Information Our industry expertise helps deliver complete Drive System Solutions that maximize production and minimize risk.
DC Bus Inductor not connected. A valid start will override this command.
Fault Descriptions for a description of fault types. Some local codes may require redundant ground connections. Page 55 Enables the output to be controlled by bit 6 of the logic command word.
22F-A4P2N – – Allen Bradley – PowerFlex 4M kW (1 Hp) AC Drive
To view commonly ordered and quickly available products, use the Product Configuration Assistant for our complete product offerings. Opening the Cover 1. Brxdley text from picture: Sets the time between restart attempts when A [Auto Rstrt Tries] is set to a value other than zero.
HERTZ that group will flash. Page 40 Start Up Notes: Each digital input draws 6 mA. ProposalWorks — Build complete quotes and proposals. Learn More Additional software products are available from Rockwell Software. Tighten the screw to keep it in place. Page 90 This 4 is suitable for use with a cable length up to meters feet for Class A and 25 meters 82 feet for Class B environments.
Don’t show me this message again. Page 46 Main Control Board software version. Appendix B Refer to for accessory ordering information. Stop input also clears active fault. Start and Direction commands come from P [Start Source]. Product Certifications Certifications apply when product is marked.
ALLEN BRADLEY POWERFLEX 4M USER MANUAL Pdf Download.
Power must be applied to the drive to perform the following start-up procedures. If this condition is unacceptable, the bus regulator must be disabled see parameter A Table of Contents Add to my manuals Add. Do not create a program that frequently uses configurable allwn to write parameter data to NVS unless C [Comm Write Mode] is set to option 1. To simplify drive setup, the most commonly programmed parameters are organized in a single Basic Program Group. Comments to this Manuals Your Name.
When using a Powwerflex Self-Protected Type E Combination Motor Controller, the drive must be installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this column. Drive will not power up without a jumper or inductor connected.
Down Arrow Enter Advance one step in programming menu. Page 20 If it is necessary to disconnect power to the motor with the drive outputting power, an auxiliary contact should be used to simultaneously disable drive control run commands. Page 97 Catalog Number: Communications Group Stops drive via coast to stop.
TOP 10 Related
Allen-Bradley, Rockwell Automation, and PowerFlex are registered trademarks of PowerFlex 4M Adjustable Frequency Drive FRN – User Manual. I/O Wiring. PowerFlex 4M Quick Start Guide. Display. Parameter Group. First Shown when drive powered up. Display Group. (View Only). Basic Program Group. View and Download ALLEN BRADLEY PowerFlex 4M user manual online. FRN 1 Series, FRN 2 Series, Adjustable Frequency AC Drive. PowerFlex 4M.
Allen Bradley Powerflex 4 Programming Manual Pdf
Author: | Vudozragore Samukazahn |
Country: | Burma |
Language: | English (Spanish) |
Genre: | Politics |
Published (Last): | 11 June 2006 |
Pages: | 224 |
PDF File Size: | 4.42 Mb |
ePub File Size: | 18.57 Mb |
ISBN: | 392-4-28661-434-6 |
Downloads: | 44527 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Mikaktilar |
Description for bits 6, 7, and 15 of register address updated. Information on reading register address clarified.
Guidelines on standard RS wiring practices added. Description for option 21 of parameter t [Relay Out Sel] corrected. D-2 Connecting an RS Network. Safety Guidelines for the SGI If this condition is unacceptable, the bus regulator must be disabled see parameter A In addition, installing a properly sized dynamic brake resistor will provide equal or better performance in most cases. See Appendix B for details. Opening the Cover 1. Press and hold in the tabs on each side of the cover.
Pull the cover out and up to release. Pull the jumper completely out of the drive chassis. Tighten the screw to keep it in place. Tighten screw after jumper removal. Appendix B Refer to for accessory ordering information. Motor Ground The motor ground must be connected powedflex one of the ground terminals on the drive. Some local codes may require redundant ground connections.
The integrity of all connections should be periodically checked. The ratings in the table that follows are the maximum recommended values for use with each drive rating.
The devices listed in this table are provided to serve as a manjal. When using a Manual Self-Protected Type E Combination Motor Controller, the drive must be installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this column. Application specific thermal considerations may require a larger enclosure.
Do not use THHN or similarly coated wire in wet areas.
Any wire chosen must have a minimum insulation thickness of 15 mils and should not have large variations in insulation concentricity. If it is necessary to disconnect power to the motor with the drive outputting power, an auxiliary contact should be used to simultaneously disable drive control run commands. Drive will not power up without a jumper or inductor connected.
When the AC line is removed, there will be a loss of any inherent regenerative braking effect that might be present – the motor will coast to a stop. An auxiliary braking method may be required.
Each digital input draws 6 mA. All drives must be powered up for the analog signal to be read correctly. Run 4 specified by P [Speed Reference].
Start and Direction commands come from P [Start Source]. Keep wire length as short as possible between the enclosure entry point and the EMI filter. Installations on a public low voltage power network may require additional external harmonic mitigation. To simplify drive setup, the most commonly programmed parameters are organized in a single Basic Program Group.
Read the General Precautions section before proceeding. Power must be applied to the drive to perform the following start-up procedures. Scroll through groups and parameters. Down Arrow Enter Advance one step in programming menu. Save a change to a parameter value. HERTZ that group will flash. Press the Up Arrow or Down Arrow aolen scroll through the parameters in the group. Press Enter or Sel to enter the group menu again. The Basic Program Group page contains the most commonly changed parameters.
Parameters marked 32 bit will have two parameter numbers when using RS communications and programming software. Based on Drive Rating Display: When this bit is a 1 the drive can be started.
22F-A4P2N – – Allen Bradley – PowerFlex 4M kW (1 Hp) AC Drive
When this bit is a 0 the drive will stop. Main Control Board software version. A Stop drive before changing this parameter. Sets the highest frequency the drive will output.
Stop input also clears active fault. A valid start will override this command. Enables the output to usr controlled by bit 6 of the logic command word. Stops drive via coast to stop. Do not create a program that frequently uses configurable outputs to write parameter data to NVS unless C [Comm Write Mode] is set to option 1.
Sets the frequency at which the drive will not operate. A setting of 0 disables this parameter. Refer to parameter A Brake Level].
PowerFlex 4M AC Drives
When set to a value other than zero, d [Process Display] indicates the duration of the bradey. Sets the time between restart attempts when A [Auto Rstrt Tries] is set to a value other than zero. Values Default Drive Rated Amps 0. Chapter Troubleshooting Chapter 4 provides information to guide you in troubleshooting the PowerFlex 4M drive. Included is a listing and description of drive faults with possible solutions, when applicable.
Type 2 that indicate possible drive component malfunction are not qllen. Caution should be used when enabling this feature, since the drive will attempt to issue its own start command based on user selected programming.
Failure has been detected in the 1. Replace drive if fault cannot be cleared. DC Bus Inductor not connected. Internal brake IGBT included with power ratings 5. See Appendix B for ordering information. Supplemental Drive Information Notes: Alternative resistors may be used, however care must be taken when making a selection.
Requires two resistors wired in parallel. This filter brradley suitable for use with a cable length up to meters feet for Class A and 25 meters 82 feet for Class B environments. Windows 98, ME, NT 4. Applicable to Frame C drives only.
In addition, some Modbus functions are supported to allow simple networking.
PowerFlex 4M AC Drives
Controller For information regarding DeviceNet or other communication protocols, refer to the appropriate user manual. Returns the same data as Reading 03 Parameter d [Output Freq]. Additional Information Refer to for additional information. Page of Go.
Table of Contents Add to my manuals Add. Chapters Table Of Contents Page 3 Description for bits 6, 7, and 15 of register address updated. Page 4 Description for option 21 of parameter t [Relay Out Sel] corrected. Table Of Contents Product Selection General Precautions 1 minute. Catalog Number Explanation Ac Supply Source Considerations 2. Page 16 Some local codes may require redundant ground connections. Page 18 When using a Manual Self-Protected Type E Combination Motor Controller, the drive must be installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this column.
Allen Bradley Powerflex 4m Manual
Page 20 If it is necessary to disconnect power to the motor with manuap drive outputting power, an auxiliary contact should be used to simultaneously disable drive control run commands. Page 21 Drive will not power up without a jumper or inductor connected. Page 22 When powerfleex AC line is removed, there will be a loss of any inherent regenerative braking effect that might be present – the motor will coast to a stop.
Powerflex 4m Parameter Manual Pdf Compressor
Page 26 Each digital input draws 6 mA. Page 27 Direction Mode]. Page 30 Preset Frequency.